Design and copyright by Tomi Engdahl 1996,1999
This is my VGA to TV circuit I have designed at 1996 for one one company I worked for. Since this design is no longer in production and my agreement has ended, I ma free to publish the details on the web.
Note: The cocuments is based on my notes from more than two years back (1996). I haven't developed the circuit since then.
This circuit diagram is as I draw it at 1996. I hope this drawing is entirely correct, because I have not done much with my documents since end of 1996.
Click picture for high resolution picture or download Postscript version of the circuit diagram.
Note: There is one mistakes on the circuit diagram which should be
This circuit is based on AD722 IC from Analog Devices. The AD722 is a low cost RGB to NTSC/PAL Encoder that converts red, green and blue color component signals into their corresponding luminance (baseband amplitude) and chrominance (subcarrier amplitude and phase) signals in accordance with either NTSC or PAL standards. These two outputs are also combined to provide composite video output. All the outputs can drive standard 75 ohm terminated video cables directly without extra amplifiers. The chip is a very compact solution, because operates from a single +5 V supply and it need no external delay lines or filters.
Because the AD722 IC does almost everything necessary, only very little extra electronics is needed. The chip needs external clock crystals to operate, so the circuit provides the color subcarrier frequency crystals: 4.43MHz for PAL and 3.58MHz for NTSC. The circuit here also provides necessary components for power decoupling and proper termiantion of video lines (inputs and outputs).
The most complicated part of the circuit is the sync signal processing. Because the sync signals from VGA card can be at any polarity, U1 and circuit around it will guarantee that the sync signal are always correct polarity when they enter AD722 conversion IC (U1 makes polarity inversion if needed). The circuit as this would already work, but with some VGA card on some grpahics modes it is hard to generate HSYNC signal which has exactly right width. The HSYNC width must be quite accurately correct for proper color video signal receoption, so I thought it was a good idea to add a circuit which would generate a sync signal which always has right pulsewidth. In this circuit monostable multibirato built around U2 (555 timer) generates the right pulse width for HSYNC signal. The pulse width of this circuit is adjusted using R4.
When using this circuit a right VGA to TV driver must be loaded. This driver does the job of making the VGA card to generae the picture signals at right format and refresh rate. The drivers which cna be used with this circuit are the same as with my VGA to SCART circuit. You have to select a driver which matches the video standard you want to output.
Then you have to select the output standard on the circuit to match the vide output standard. Use the following table to set the switched SW1 and SW2 to match the video output standard you want to use:
Standard SW1 SW2 PAL Closed Up NTSC Open DownYou must adjust also the width of HSYNC signal using R4. NTSC signal asks for 4.59 microsecond HSYNC signal and PAL asks for 4.60 microsecond HSYNC signal. If the HSYNC signal pulse width is not right, quite many TVs have problems in receiving the color signal correctly or even sync to the video signal at all. Best option to adjust the HSYNC signal is to use some measuring equipment like oscilloscope, video vectorscope or frequency counter (which has period measurement capabilities). If you don't have the necessary measusing equipments, you have just to adjust R4 so that you get the colors workign well with your TV. Basically uou have to adjust this setting once, because when you get the setting right, the same setting usually works for PAL and NTSC standard (they timing is so near each other in this).
The last setting is to to fine-tune the color subcarrier frequency. C6 adjusts NTSC subcarrier frequency and C7 adjusts PAL subcarrier frequency. You have to adjust those so that you get the best color reproduction. You have access to vectorscope or similar vidoe signal analyzer, you can use it to fine-tune the color subcarrier frequency to be exactly right. Otherwise you have just to approximate what is the best setting for your TV.
site part value ==== ====== ========== C1 22uF C10 100nF C11 10uF C12 220uF C13 220uF C14 220uF C15 100uF C16 100nF C17 100nF C18 100uF C2 22uF C3 1 nF C3' 220nF C4 100nF C5 15nF C6 10-30pF C7 10-30pF C8 10uF C9 100nF D1 1N4001 P1 15 pin VGA connector R1 2K2 R2 2K2 R3 10K R4 1K R5 75R R6 75R R7 75R U1 74LS86 U2 ne555 U3 AD722JR-16 U4 7805 regulator IC Y1 3.58MHz crystal Y2 4.43MHz crystalOther items needed:
I have built my first prototypes to a veroboard. This method worked very well with other componets on the circuit than the AD722 IC, which was only available in SOIC enclosure. I built my first prototype by carefully solvering small wires to each pin in the AD722 IC and then soledered those to veroboard (not an easy task and fun to do).
The later prototypes I built to the following circuit board (click the picture for larger view, 300x300 dpi scanned picture):
You can print out the picture at correct resolution to a laser printer (6.83x3.87 inches) to a slide and propaly use it as a mask for making a circuit board of your own. If you have a postscript printer or a suitable viewer/printing program you can download zipped Postscript version of the circuit board which automatically prints to right size.
I don't have a nicely drawn out component placement diagram. I found an old paper version of one component placement diagram which might be helful:
It is not very clear and does not show orientation of all components, so you have to figure out that part of circuit construction yourself. That's all I can provide at the moments (I don't have my old protoype circuit boards anymore).